Nev Posted December 10, 2005 Share Posted December 10, 2005 I've got some new shutters to fit and I've been supplied with hinge pins (gonds) with an expanding bolt fastening. This requires a 16mm hole for which I've got the necessary SDS bit etc but my question is how tight do you fasten them? They need to be inserted to a fairly accurate depth in order to get the correct vertical alignment with the face of the wall, but I can't decide how to do it. I haven't actually tried yet! I was assuming that I'd insert the gond and then give it 1 (or 2 or 3?) complete turns to tighten. I forgot to mention, this is into nicely dressed stone around the window aperture, so I don't want to split it or damage it! Nev Link to comment Share on other sites More sharing options...
Deimos Posted December 10, 2005 Share Posted December 10, 2005 I don’t know the answer as to how tight, but there is stoneand stone. I have tuffeau andsome blocks can be very weak and split quite easily (e.g. screw into aplug). I would imagine that a lot ofthe load when the shutters are hung will be vertical. Ian Link to comment Share on other sites More sharing options...
Nev Posted December 10, 2005 Author Share Posted December 10, 2005 DeimosTuffeau?? I have the Charente limestone.You're right about the vertical load, except when the shutter swings open, in which case the top hinge pin will, I guess, have an momentary outward pull when the shutter is 90 degrees to the wall.Nev. Link to comment Share on other sites More sharing options...
Nev Posted December 10, 2005 Author Share Posted December 10, 2005 It wasn't a problem in the end. Drilled the hole with my new super-cheap SDS drill (Castorama - 29.99€), inserted the hinge-pin and tightened until firm. Link to comment Share on other sites More sharing options...
Dave&Olive Posted December 10, 2005 Share Posted December 10, 2005 hi I have found out by my mistakes it is easier to use the chem fix ones , these give you a little bit of lea way and donnot burst the stone , best to drill in at an angle ie gives more strength . dave Link to comment Share on other sites More sharing options...
Nev Posted December 11, 2005 Author Share Posted December 11, 2005 DaveI presume you mean at an angle left or right? Anything other than perfectly horizontal means that the pin wouldn't be vertical.I looked at the chemical ones and decided that they were meant for beton blocks. Although I've had no splits so far, I think you are right, and I will try those for the next set of shutters. They work out a little more expensive with the tube of resin. How long do they take to set?Nev Link to comment Share on other sites More sharing options...
Dave&Olive Posted December 11, 2005 Share Posted December 11, 2005 hi well you got my drift .... how long do they take to set??? depends on the weather !!! no joke from seconds to ....a few more seconds in the winter. dave Link to comment Share on other sites More sharing options...
Chas Posted December 12, 2005 Share Posted December 12, 2005 We had our shutters made and hung by our local menuisier a few years ago. Having fitted and wedged the shutters in position he then used a jig fitted over the shutter hinge and drilled in at 45 degrees on the corner of the block and fixed with (hilti?) chemical compound. Presumably this gives the maximum support from the stone and helps avoid splitting. Link to comment Share on other sites More sharing options...
Nev Posted December 12, 2005 Author Share Posted December 12, 2005 Thanks Chas and Dave [:)]The idea of going in at 45 degrees never occurred to me. I've 3 more to do so I'll try that.Nev Link to comment Share on other sites More sharing options...
Dave&Olive Posted December 12, 2005 Share Posted December 12, 2005 hi like i said i learnt by my mistakes,,,,, if you do drill in at an angle you need to move the hole over to allow for the angle ...you will see what i mean when your first hinge is 5/8ths " out . davedo at test hole first Link to comment Share on other sites More sharing options...
Chas Posted December 13, 2005 Share Posted December 13, 2005 hi like i said i learnt by my mistakes,,,,, if you do drill in at an angle you need to move the hole over to allow for the angle ...you will see what i mean when your first hinge is 5/8ths " out . davedo at test hole firstI presume that's why my guy had a drilling jig that slipped over the shutter hinge pin Link to comment Share on other sites More sharing options...
Nev Posted December 13, 2005 Author Share Posted December 13, 2005 I've got the drilling guide; it's a "gabarit de percage"; from LaPeyre, 4,40€, and I reckon it's worth it's weight in gold! It bolts into the hinge to give the correct position for the hole.I've got a picture of it but just realised I can't insert images here, doh!I can see what you mean about being slightly out, but with the guide it'll be correct, although I'm in two minds now... I've had a look around the house at the existing hinge pins and they're all at 90 degrees to the wall.I used to be indecisive, but now I'm not so sure.Nev Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.